91 lines
2.9 KiB
C
91 lines
2.9 KiB
C
// Copyright 2021 IOsetting <iosetting(at)outlook.com>
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
/**
|
|
* Demo: 2-channel with timer2 interrupt
|
|
*
|
|
* P1.0 -> 1k Ω resistor -> LED1+
|
|
* P1.1 -> 1k Ω resistor -> LED2+
|
|
* GND -> LED1-
|
|
* GND -> LED2-
|
|
*/
|
|
#include "fw_hal.h"
|
|
|
|
__BIT dir = SET;
|
|
uint8_t dc = 0;
|
|
|
|
INTERRUPT(Timer2_Routine, EXTI_VectTimer2)
|
|
{
|
|
PWMA_PWM1_SetCaptureCompareValue(dc);
|
|
UART1_TxHex(dc);
|
|
UART1_TxString("\r\n");
|
|
if (dir)
|
|
{
|
|
dc++;
|
|
if (dc == 0xFF) dir = !dir;
|
|
}
|
|
else
|
|
{
|
|
dc--;
|
|
if (dc == 0) dir = !dir;
|
|
}
|
|
}
|
|
|
|
void main(void)
|
|
{
|
|
SYS_SetClock();
|
|
// UART1, baud 115200, baud source Timer1, 1T mode
|
|
UART1_Config8bitUart(UART1_BaudSource_Timer1, HAL_State_ON, 115200);
|
|
|
|
// Set GPIO pins output mode
|
|
GPIO_P1_SetMode(GPIO_Pin_0|GPIO_Pin_1, GPIO_Mode_Output_PP);
|
|
// Turn off PWMA.1 before change its mode
|
|
PWMA_PWM1_SetPortState(HAL_State_OFF);
|
|
PWMA_PWM1N_SetPortState(HAL_State_OFF);
|
|
// Set PWMA.1 port direction output
|
|
PWMA_PWM1_SetPortDirection(PWMB_PortDirOut);
|
|
// Set PWMA.1 output low voltage when counter is less than target value
|
|
PWMA_PWM1_ConfigOutputMode(PWM_OutputMode_PWM_LowIfLess);
|
|
// Enable comparison value preload to make duty cycle changing smooth
|
|
PWMA_PWM1_SetComparePreload(HAL_State_ON);
|
|
// Turn on PWMA.1
|
|
PWMA_PWM1_SetPortState(HAL_State_ON);
|
|
// Turn on PWMA.1 complementary output
|
|
PWMA_PWM1N_SetPortState(HAL_State_ON);
|
|
// Set highest PWM clock
|
|
PWMA_SetPrescaler(0);
|
|
// PWM width = Period + 1 (side alignment), or AutoReloadPeriod * 2 (center alignment)
|
|
PWMA_SetPeriod(0xFF);
|
|
// Counter direction, down:from [PWMA_ARRH,PWMA_ARRL] to 0
|
|
PWMA_SetCounterDirection(PWM_CounterDirection_Down);
|
|
// Enable preload on reload-period
|
|
PWMA_SetAutoReloadPreload(HAL_State_ON);
|
|
// Enable output on PWMA.1P, PWMA.1N
|
|
PWMA_SetPinOutputState(PWM_Pin_1|PWM_Pin_1N, HAL_State_ON);
|
|
// Set PWMA.1 alternative ports to P1.0 and P1.1
|
|
PWMA_PWM1_SetPort(PWMA_PWM1_AlterPort_P10_P11);
|
|
// Enable overall output
|
|
PWMA_SetOverallState(HAL_State_ON);
|
|
// Start counter
|
|
PWMA_SetCounterState(HAL_State_ON);
|
|
|
|
// 1T mode, prescaler:255+1, frequency: 100
|
|
TIM_Timer2_Config(HAL_State_ON, 0xFF, 100);
|
|
// Timer2 interrupt: ON
|
|
EXTI_Timer2_SetIntState(HAL_State_ON);
|
|
EXTI_Global_SetIntState(HAL_State_ON);
|
|
TIM_Timer2_SetRunState(HAL_State_ON);
|
|
|
|
while(1);
|
|
} |