95 lines
2.5 KiB
C
95 lines
2.5 KiB
C
// Copyright 2021 IOsetting <iosetting(at)outlook.com>
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
/**
|
|
* STC8H3K64S2
|
|
* AGrnd -> GND
|
|
* AVcc -> VCC
|
|
* AVref -> VCC
|
|
* Vcc -> VCC
|
|
* Gnd -> GND
|
|
* ADC1 -> Test voltage
|
|
*
|
|
* STC8H1K08
|
|
* AVref -> VCC
|
|
* Vcc -> VCC
|
|
* Gnd -> GND
|
|
* ADC1 -> Test voltage
|
|
*/
|
|
#include "fw_hal.h"
|
|
|
|
uint8_t pos;
|
|
uint16_t res[2];
|
|
|
|
INTERRUPT(ADC_Routine, EXTI_VectADC)
|
|
{
|
|
ADC_ClearInterrupt();
|
|
res[pos] = ADC_RESL;
|
|
res[pos] |= (ADC_RES & 0x0F) << 8;
|
|
// Restart ADC for continuous sampling
|
|
pos = (pos+1) & 0x1;
|
|
if (pos == 0)
|
|
{
|
|
/**
|
|
* Uncomment these lines in high speed ADC
|
|
GPIO_P1_SetMode(GPIO_Pin_1, GPIO_Mode_InOut_OD);
|
|
GPIO_P1_SetMode(GPIO_Pin_1, GPIO_Mode_Input_HIP);
|
|
*/
|
|
ADC_SetChannel(0x01);
|
|
}
|
|
else
|
|
{
|
|
/**
|
|
* Uncomment these lines in high speed ADC
|
|
GPIO_P1_SetMode(GPIO_Pin_2, GPIO_Mode_InOut_OD);
|
|
GPIO_P1_SetMode(GPIO_Pin_2, GPIO_Mode_Input_HIP);
|
|
*/
|
|
ADC_SetChannel(0x02);
|
|
}
|
|
ADC_Start();
|
|
}
|
|
|
|
void main(void)
|
|
{
|
|
SYS_SetClock();
|
|
// For debug print
|
|
UART1_Config8bitUart(UART1_BaudSource_Timer2, HAL_State_ON, 115200);
|
|
// Channel: ADC1
|
|
ADC_SetChannel(0x01);
|
|
// ADC Clock = SYSCLK / 2 / (1+15) = SYSCLK / 32
|
|
ADC_SetClockPrescaler(0x0F);
|
|
// Right alignment, high 2-bit in ADC_RES, low 8-bit in ADC_RESL
|
|
ADC_SetResultAlignmentRight();
|
|
// Enable interrupts
|
|
EXTI_Global_SetIntState(HAL_State_ON);
|
|
EXTI_ADC_SetIntState(HAL_State_ON);
|
|
// Turn on ADC power
|
|
ADC_SetPowerState(HAL_State_ON);
|
|
// Set ADC1(P1.1), ADC2(P1.2) HIP
|
|
GPIO_P1_SetMode(GPIO_Pin_1|GPIO_Pin_2, GPIO_Mode_Input_HIP);
|
|
// Start ADC
|
|
ADC_Start();
|
|
|
|
while(1)
|
|
{
|
|
UART1_TxString("Result: ");
|
|
UART1_TxHex(res[0] >> 8);
|
|
UART1_TxHex(res[0] & 0xFF);
|
|
UART1_TxChar(' ');
|
|
UART1_TxHex(res[1] >> 8);
|
|
UART1_TxHex(res[1] & 0xFF);
|
|
UART1_TxString("\r\n");
|
|
SYS_Delay(100);
|
|
}
|
|
} |