148 lines
4.0 KiB
C
148 lines
4.0 KiB
C
// Copyright 2021 IOsetting <iosetting(at)outlook.com>
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
/***
|
|
* Demo: ST7567 12864 LCD
|
|
* Board: STC8H3K32
|
|
*
|
|
* P37 -> RES, RESET 7 - 18
|
|
* P36 -> DC, A0 8 - 17
|
|
* P35 -> CSB, Chip Select 6 - 16
|
|
* P32 -> SCK, SCL, CLK, Clock 9 - 13
|
|
* P12 -> LED-A, Backlight 3 - 19
|
|
* P34 -> MOSI, SDA 10 - 15
|
|
* GND -> GND
|
|
* 3.3V -> VCC
|
|
*/
|
|
|
|
#include "fw_hal.h"
|
|
#include "st7567.h"
|
|
|
|
|
|
void SPI_Init(void)
|
|
{
|
|
// ST7567 doesn't work if SPI frequency is too high
|
|
SPI_SetClockPrescaler(SPI_ClockPreScaler_16);
|
|
// Clock idles low
|
|
SPI_SetClockPolarity(HAL_State_OFF);
|
|
// Data transfer is driven by lower SS pin
|
|
SPI_SetClockPhase(SPI_ClockPhase_LeadingEdge);
|
|
// MSB first
|
|
SPI_SetDataOrder(SPI_DataOrder_MSB);
|
|
// Define the output pins
|
|
SPI_SetPort(SPI_AlterPort_P35_P34_P33_P32);
|
|
// Ignore SS pin, use MSTR to swith between master/slave mode
|
|
SPI_IgnoreSlaveSelect(HAL_State_ON);
|
|
// Master mode
|
|
SPI_SetMasterMode(HAL_State_ON);
|
|
// Start SPI
|
|
SPI_SetEnabled(HAL_State_ON);
|
|
}
|
|
|
|
void GPIO_Init(void)
|
|
{
|
|
// Configure GPIO pins before SPI and device
|
|
// DIN(P34)
|
|
GPIO_P3_SetMode(GPIO_Pin_4, GPIO_Mode_InOut_QBD);
|
|
// SCLK(P32)
|
|
GPIO_P3_SetMode(GPIO_Pin_2|GPIO_Pin_5|GPIO_Pin_6|GPIO_Pin_7, GPIO_Mode_Output_PP);
|
|
GPIO_P1_SetMode(GPIO_Pin_2, GPIO_Mode_Output_PP);
|
|
}
|
|
|
|
int main(void)
|
|
{
|
|
int y1, y2;
|
|
uint8_t d1, d2;
|
|
|
|
SYS_SetClock();
|
|
GPIO_Init();
|
|
SPI_Init();
|
|
ST7567_Init();
|
|
|
|
while(1)
|
|
{
|
|
ST7567_DrawLine(0, 0, 127, 0, 1);
|
|
ST7567_DrawLine(0, 0, 0, 63, 1);
|
|
ST7567_DrawLine(127, 0, 127, 63, 1);
|
|
ST7567_DrawLine(0, 63, 127, 63, 1);
|
|
|
|
ST7567_GotoXY(3, 5);
|
|
ST7567_Puts("LCD:ST7567", &Font_5x7, 1);
|
|
ST7567_GotoXY(3, 13);
|
|
ST7567_Puts("STC8 FwLib Demo", &Font_5x7, 1);
|
|
ST7567_GotoXY(3, 21);
|
|
ST7567_Puts("It's a demo of ST7567 12864 LCD", &Font_3x5, 1);
|
|
ST7567_GotoXY(3, 27);
|
|
ST7567_Puts("Font size 3x5, nums:01234567890", &Font_3x5, 1);
|
|
ST7567_GotoXY(5, 52);
|
|
ST7567_Puts("Font size: 5x7", &Font_5x7, 1);
|
|
ST7567_UpdateScreen();
|
|
SYS_Delay(2000);
|
|
|
|
y1 = 10;
|
|
while (y1 <= 0x30)
|
|
{
|
|
ST7567_SetContrast(y1++);
|
|
SYS_Delay(100);
|
|
}
|
|
while (y1 >= 10)
|
|
{
|
|
ST7567_SetContrast(y1--);
|
|
SYS_Delay(100);
|
|
}
|
|
while (y1 <= 0x20)
|
|
{
|
|
ST7567_SetContrast(y1++);
|
|
SYS_Delay(100);
|
|
}
|
|
SYS_Delay(2000);
|
|
|
|
ST7567_ToggleInvert();
|
|
ST7567_UpdateScreen();
|
|
SYS_Delay(2000);
|
|
|
|
ST7567_ToggleInvert();
|
|
ST7567_UpdateScreen();
|
|
SYS_Delay(2000);
|
|
|
|
ST7567_Fill(0);
|
|
y1 = 64, y2 = 0;
|
|
while (y1 > 0)
|
|
{
|
|
ST7567_DrawLine(0, y1, 127, y2, 1);
|
|
ST7567_UpdateScreen();
|
|
y1 -= 2;
|
|
y2 += 2;
|
|
SYS_Delay(100);
|
|
}
|
|
SYS_Delay(1000);
|
|
|
|
ST7567_Fill(0);
|
|
y1 = 127, y2 = 0;
|
|
while (y1 > 0)
|
|
{
|
|
ST7567_DrawLine(y1, 0, y2, 63, 1);
|
|
ST7567_UpdateScreen();
|
|
y1 -= 2;
|
|
y2 += 2;
|
|
SYS_Delay(100);
|
|
}
|
|
SYS_Delay(1000);
|
|
|
|
ST7567_Fill(0);
|
|
ST7567_UpdateScreen();
|
|
SYS_Delay(2000);
|
|
}
|
|
}
|