196 lines
3.6 KiB
C
196 lines
3.6 KiB
C
// Copyright 2021 IOsetting <iosetting(at)outlook.com>
|
|
//
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
// you may not use this file except in compliance with the License.
|
|
// You may obtain a copy of the License at
|
|
//
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
//
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
// See the License for the specific language governing permissions and
|
|
// limitations under the License.
|
|
|
|
/***
|
|
* Demo: AT24C08 write and read with raw registers
|
|
* Board: STC8H3K32
|
|
*
|
|
* P32 -> SCL
|
|
* P33 -> SDA
|
|
* GND -> GND, A2
|
|
* 3.3V -> VCC
|
|
*/
|
|
|
|
#include "fw_hal.h"
|
|
|
|
#define AT24C_ADDR 0xA0
|
|
|
|
|
|
void Wait()
|
|
{
|
|
while (!(I2CMSST & 0x40));
|
|
I2CMSST &= ~0x40;
|
|
}
|
|
|
|
void Start()
|
|
{
|
|
I2CMSCR = 0x01;
|
|
Wait();
|
|
}
|
|
|
|
void SendData(char dat)
|
|
{
|
|
I2CTXD = dat;
|
|
I2CMSCR = 0x02;
|
|
Wait();
|
|
}
|
|
|
|
void RecvACK()
|
|
{
|
|
I2CMSCR = 0x03;
|
|
Wait();
|
|
}
|
|
|
|
char RecvData()
|
|
{
|
|
I2CMSCR = 0x04;
|
|
Wait();
|
|
return I2CRXD;
|
|
}
|
|
|
|
void SendACK()
|
|
{
|
|
I2CMSST = 0x00;
|
|
I2CMSCR = 0x05;
|
|
Wait();
|
|
}
|
|
|
|
void SendNAK()
|
|
{
|
|
I2CMSST = 0x01;
|
|
I2CMSCR = 0x05;
|
|
Wait();
|
|
}
|
|
|
|
void Stop()
|
|
{
|
|
I2CMSCR = 0x06;
|
|
Wait();
|
|
}
|
|
|
|
void I2C_Init(void)
|
|
{
|
|
// Master mode
|
|
I2C_SetWorkMode(I2C_WorkMode_Master);
|
|
/**
|
|
* I2C clock = FOSC / 2 / (__prescaler__ * 2 + 4)
|
|
*/
|
|
I2C_SetClockPrescaler(0x20);
|
|
// Switch alternative port
|
|
I2C_SetPort(I2C_AlterPort_P32_P33);
|
|
// Start I2C
|
|
I2C_SetEnabled(HAL_State_ON);
|
|
}
|
|
|
|
void GPIO_Init(void)
|
|
{
|
|
// SDA
|
|
GPIO_P3_SetMode(GPIO_Pin_3, GPIO_Mode_InOut_QBD);
|
|
// SCL
|
|
GPIO_P3_SetMode(GPIO_Pin_2, GPIO_Mode_Output_PP);
|
|
}
|
|
|
|
int main(void)
|
|
{
|
|
uint8_t i, buf[20];
|
|
|
|
SYS_SetClock();
|
|
// UART1 configuration: baud 115200 with Timer2, 1T mode, no interrupt
|
|
UART1_Config8bitUart(UART1_BaudSource_Timer2, HAL_State_ON, 115200);
|
|
|
|
GPIO_Init();
|
|
I2C_Init();
|
|
|
|
P_SW2 |= 0x80;
|
|
|
|
Start();
|
|
SendData(AT24C_ADDR);
|
|
RecvACK();
|
|
SendData(0x00);
|
|
RecvACK();
|
|
SendData(0xAF);
|
|
RecvACK();
|
|
SendData(0xBF);
|
|
RecvACK();
|
|
SendData(0xCF);
|
|
RecvACK();
|
|
SendData(0xDF);
|
|
RecvACK();
|
|
SendData(0xEF);
|
|
RecvACK();
|
|
SendData(0xFF);
|
|
RecvACK();
|
|
Stop();
|
|
SYS_Delay(50);
|
|
|
|
while (1)
|
|
{
|
|
Start();
|
|
SendData(AT24C_ADDR);
|
|
RecvACK();
|
|
SendData(0x00);
|
|
RecvACK();
|
|
Start();
|
|
SendData(AT24C_ADDR|0x01);
|
|
RecvACK();
|
|
buf[0] = RecvData();
|
|
SendACK();
|
|
buf[1] = RecvData();
|
|
SendNAK();
|
|
Stop();
|
|
UART1_TxHex(buf[0]);
|
|
UART1_TxChar(':');
|
|
UART1_TxHex(buf[1]);
|
|
UART1_TxChar(' ');
|
|
|
|
Start();
|
|
SendData(AT24C_ADDR);
|
|
RecvACK();
|
|
SendData(0x01);
|
|
RecvACK();
|
|
Start();
|
|
SendData(AT24C_ADDR|0x01);
|
|
RecvACK();
|
|
buf[0] = RecvData();
|
|
SendACK();
|
|
buf[1] = RecvData();
|
|
SendNAK();
|
|
Stop();
|
|
UART1_TxHex(buf[0]);
|
|
UART1_TxChar(':');
|
|
UART1_TxHex(buf[1]);
|
|
UART1_TxChar(' ');
|
|
|
|
Start();
|
|
SendData(AT24C_ADDR);
|
|
RecvACK();
|
|
SendData(0x02);
|
|
RecvACK();
|
|
Start();
|
|
SendData(AT24C_ADDR|0x01);
|
|
RecvACK();
|
|
buf[0] = RecvData();
|
|
SendACK();
|
|
buf[1] = RecvData();
|
|
SendNAK();
|
|
Stop();
|
|
UART1_TxHex(buf[0]);
|
|
UART1_TxChar(':');
|
|
UART1_TxHex(buf[1]);
|
|
UART1_TxChar(' ');
|
|
|
|
SYS_Delay(200);
|
|
}
|
|
}
|