2022-01-01 10:43:23 +01:00
|
|
|
// Copyright 2021 IOsetting <iosetting(at)outlook.com>
|
|
|
|
|
//
|
|
|
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
|
|
|
|
// you may not use this file except in compliance with the License.
|
|
|
|
|
// You may obtain a copy of the License at
|
|
|
|
|
//
|
|
|
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
|
|
|
|
//
|
|
|
|
|
// Unless required by applicable law or agreed to in writing, software
|
|
|
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
|
|
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
|
|
|
// See the License for the specific language governing permissions and
|
|
|
|
|
// limitations under the License.
|
|
|
|
|
|
|
|
|
|
#include "fw_hal.h"
|
|
|
|
|
|
|
|
|
|
__BIT dir = SET;
|
|
|
|
|
uint8_t dc = 0;
|
|
|
|
|
|
|
|
|
|
void main(void)
|
|
|
|
|
{
|
|
|
|
|
SYS_SetClock();
|
|
|
|
|
// UART1, baud 115200, baud source Timer1, 1T mode, no interrupt
|
2022-01-09 12:26:52 +01:00
|
|
|
UART1_Config8bitUart(UART1_BaudSource_Timer1, HAL_State_ON, 115200);
|
2022-01-01 10:43:23 +01:00
|
|
|
|
|
|
|
|
// Set GPIO pin mode
|
|
|
|
|
GPIO_P3_SetMode(GPIO_Pin_2|GPIO_Pin_3, GPIO_Mode_Output_PP);
|
|
|
|
|
|
|
|
|
|
// Stop PCA/PWM
|
|
|
|
|
PCA_SetCounterState(HAL_State_OFF);
|
|
|
|
|
// Stop counter in idle mode
|
|
|
|
|
PCA_SetStopCounterInIdle(HAL_State_ON);
|
|
|
|
|
// Use SYSCLK as clock source
|
|
|
|
|
PCA_SetClockSource(PCA_ClockSource_SysClk);
|
|
|
|
|
// Turn off overflow interrupt
|
|
|
|
|
PCA_EnableCounterOverflowInterrupt(HAL_State_OFF);
|
|
|
|
|
|
|
|
|
|
// Set PCA0 and PCA1 to PWM mode
|
|
|
|
|
PCA_PCA0_SetWorkMode(PCA_WorkMode_PWM_NonInterrupt);
|
|
|
|
|
PCA_PCA1_SetWorkMode(PCA_WorkMode_PWM_NonInterrupt);
|
|
|
|
|
// Set both to 8-bit PWM
|
|
|
|
|
PCA_PWM0_SetBitWidth(PCA_PWM_BitWidth_8);
|
|
|
|
|
PCA_PWM1_SetBitWidth(PCA_PWM_BitWidth_8);
|
|
|
|
|
// Set initial duty cycle
|
|
|
|
|
PCA_PCA0_SetCompareValue(dc);
|
|
|
|
|
PCA_PCA1_SetCompareValue(~dc);
|
|
|
|
|
// Set output port for STC8G1K08A, PWM0:P32, PWM1:P33
|
|
|
|
|
PCA_SetPort(PCA_AlterPort_G1K08A_P55_P32_P33_P54);
|
|
|
|
|
// Start PWM
|
|
|
|
|
PCA_SetCounterState(HAL_State_ON);
|
|
|
|
|
|
|
|
|
|
while(1)
|
|
|
|
|
{
|
|
|
|
|
PCA_PCA0_ChangeCompareValue(dc);
|
|
|
|
|
PCA_PCA1_ChangeCompareValue(~dc);
|
|
|
|
|
UART1_TxHex(dc);
|
|
|
|
|
UART1_TxChar(' ');
|
|
|
|
|
UART1_TxHex(~dc);
|
|
|
|
|
if (dir)
|
|
|
|
|
{
|
|
|
|
|
dc++;
|
|
|
|
|
if (dc == 0xFF) dir = !dir;
|
|
|
|
|
}
|
|
|
|
|
else
|
|
|
|
|
{
|
|
|
|
|
dc--;
|
|
|
|
|
if (dc == 0) dir = !dir;
|
|
|
|
|
}
|
|
|
|
|
UART1_TxString("\r\n");
|
|
|
|
|
SYS_Delay(10);
|
|
|
|
|
}
|
|
|
|
|
}
|
