83 lines
2.7 KiB
C
83 lines
2.7 KiB
C
|
// Copyright 2021 IOsetting <iosetting(at)outlook.com>
|
||
|
|
//
|
||
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
||
|
|
// you may not use this file except in compliance with the License.
|
||
|
|
// You may obtain a copy of the License at
|
||
|
|
//
|
||
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
||
|
|
//
|
||
|
|
// Unless required by applicable law or agreed to in writing, software
|
||
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
||
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
// See the License for the specific language governing permissions and
|
||
|
|
// limitations under the License.
|
||
|
|
|
||
|
|
/**
|
||
|
|
* Scan to find most close VRTRIM and IRTRIM for specified frequency.
|
||
|
|
*
|
||
|
|
* Change build_flags in platformio.ini
|
||
|
|
* D__CONF_FOSC -> target frequency, e.g. 36864000UL
|
||
|
|
* D__CONF_MCU_MODEL -> MCU type, e.g. MCU_MODEL_STC8H3K64S2
|
||
|
|
* D__CONF_IRCBAND -> frequency band depending on the frequency
|
||
|
|
* STC8H1K - 00:20MHz, 01:35MHz
|
||
|
|
* STC8H3K,STC8H8K - 02:24MHz, 03:40MHz
|
||
|
|
*
|
||
|
|
* Connect UART at baud 115200 and read output, when the output is not garbled,
|
||
|
|
* find the middle value of VRTRIM and IRTRIM, lower VRTRIM is preferred
|
||
|
|
*/
|
||
|
|
#include "fw_hal.h"
|
||
|
|
|
||
|
|
|
||
|
|
uint8_t readCode(uint8_t offset)
|
||
|
|
{
|
||
|
|
return (*(unsigned char volatile __CODE *)(__CID_ADDR + offset));
|
||
|
|
}
|
||
|
|
|
||
|
|
void main(void)
|
||
|
|
{
|
||
|
|
uint8_t i, j, vrtrim = 0x01, irtrim = 0;
|
||
|
|
|
||
|
|
// Set system clock. Invoke it to set the frequency band
|
||
|
|
SYS_SetClock();
|
||
|
|
// UART1 configuration: baud 115200 with Timer2, 1T mode, no interrupt
|
||
|
|
UART1_Config8bitUart(UART1_BaudSource_Timer2, HAL_State_ON, 115200);
|
||
|
|
|
||
|
|
while(1)
|
||
|
|
{
|
||
|
|
// The upper limit of IRTRIM depends on VRTRIM, MCU becomes unstable if it goes
|
||
|
|
// too high, set 0x30 to a lower value if scan stucks at beginning
|
||
|
|
if (++irtrim == 0x30 + vrtrim)
|
||
|
|
{
|
||
|
|
irtrim = 0x00;
|
||
|
|
// VRTRIM controls the voltage level, normally it won't exceed 0x40
|
||
|
|
if (++vrtrim == 0x40)
|
||
|
|
{
|
||
|
|
vrtrim = 0x00;
|
||
|
|
}
|
||
|
|
}
|
||
|
|
SYS_TrimClock(vrtrim, irtrim);
|
||
|
|
|
||
|
|
UART1_TxString("ADDR: 0x");
|
||
|
|
UART1_TxHex(__CID_ADDR >> 8);
|
||
|
|
UART1_TxHex(__CID_ADDR & 0xFF);
|
||
|
|
UART1_TxString("\r\n");
|
||
|
|
UART1_TxString("MCUID: ");
|
||
|
|
for (j = 0; j < 7; j++)
|
||
|
|
{
|
||
|
|
UART1_TxHex(readCode(18 + j));
|
||
|
|
UART1_TxChar(' ');
|
||
|
|
}
|
||
|
|
UART1_TxString("\r\n");
|
||
|
|
UART1_TxString("Current IRCBAND:");
|
||
|
|
UART1_TxHex(IRCBAND);
|
||
|
|
UART1_TxString(", VRTRIM:");
|
||
|
|
UART1_TxHex(VRTRIM);
|
||
|
|
UART1_TxString(", IRTRIM:");
|
||
|
|
UART1_TxHex(IRTRIM);
|
||
|
|
UART1_TxString(", LIRTRIM:");
|
||
|
|
UART1_TxHex(LIRTRIM);
|
||
|
|
UART1_TxString("\r\n\r\n");
|
||
|
|
|
||
|
|
SYS_Delay(50);
|
||
|
|
}
|
||
|
|
}
|