83 lines
2.1 KiB
C
83 lines
2.1 KiB
C
|
// Copyright 2021 IOsetting <iosetting(at)outlook.com>
|
||
|
|
//
|
||
|
|
// Licensed under the Apache License, Version 2.0 (the "License");
|
||
|
|
// you may not use this file except in compliance with the License.
|
||
|
|
// You may obtain a copy of the License at
|
||
|
|
//
|
||
|
|
// http://www.apache.org/licenses/LICENSE-2.0
|
||
|
|
//
|
||
|
|
// Unless required by applicable law or agreed to in writing, software
|
||
|
|
// distributed under the License is distributed on an "AS IS" BASIS,
|
||
|
|
// WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
||
|
|
// See the License for the specific language governing permissions and
|
||
|
|
// limitations under the License.
|
||
|
|
|
||
|
|
/***
|
||
|
|
* Demo: AT24C32
|
||
|
|
* Board: STC8H3K32
|
||
|
|
*
|
||
|
|
* P32 -> SCL
|
||
|
|
* P33 -> SDA
|
||
|
|
* GND -> GND, A0, A1, A2
|
||
|
|
* 3.3V -> VCC
|
||
|
|
*/
|
||
|
|
|
||
|
|
#include "fw_hal.h"
|
||
|
|
|
||
|
|
// AT24C device address, change according to the voltage level of A0/A1/A2
|
||
|
|
#define AT24C_ADDR 0xA0
|
||
|
|
// Test data
|
||
|
|
__CODE int8_t dat[20] = {0xC0,0xC1,0xC2,0xC3,0xC4,0xC5,0xC6,0xC7,0xC8,0xC9,0xCA,0xCB};
|
||
|
|
|
||
|
|
void I2C_Init(void)
|
||
|
|
{
|
||
|
|
// Master mode
|
||
|
|
I2C_SetWorkMode(I2C_WorkMode_Master);
|
||
|
|
/**
|
||
|
|
* I2C clock = FOSC / 2 / (__prescaler__ * 2 + 4)
|
||
|
|
*/
|
||
|
|
I2C_SetClockPrescaler(0x3F);
|
||
|
|
// Switch alternative port
|
||
|
|
I2C_SetPort(I2C_AlterPort_P32_P33);
|
||
|
|
// Start I2C
|
||
|
|
I2C_SetEnabled(HAL_State_ON);
|
||
|
|
}
|
||
|
|
|
||
|
|
void GPIO_Init(void)
|
||
|
|
{
|
||
|
|
// SDA
|
||
|
|
GPIO_P3_SetMode(GPIO_Pin_3, GPIO_Mode_InOut_QBD);
|
||
|
|
// SCL
|
||
|
|
GPIO_P3_SetMode(GPIO_Pin_2, GPIO_Mode_Output_PP);
|
||
|
|
}
|
||
|
|
|
||
|
|
int main(void)
|
||
|
|
{
|
||
|
|
uint8_t offset, i, buf[20];
|
||
|
|
|
||
|
|
SYS_SetClock();
|
||
|
|
// UART1 configuration: baud 115200 with Timer2, 1T mode, no interrupt
|
||
|
|
UART1_Config8bitUart(UART1_BaudSource_Timer2, HAL_State_ON, 115200);
|
||
|
|
|
||
|
|
GPIO_Init();
|
||
|
|
I2C_Init();
|
||
|
|
I2C_Write16BitAddr(AT24C_ADDR, 0x0000, dat, 12);
|
||
|
|
|
||
|
|
while(1)
|
||
|
|
{
|
||
|
|
for (offset = 0; offset < 4; offset++)
|
||
|
|
{
|
||
|
|
I2C_Read16BitAddr(AT24C_ADDR, 0x0000|offset, buf, 6);
|
||
|
|
for (i = 0; i < 6; i++)
|
||
|
|
{
|
||
|
|
UART1_TxHex(buf[i]);
|
||
|
|
UART1_TxChar(':');
|
||
|
|
}
|
||
|
|
UART1_TxString(" ");
|
||
|
|
SYS_Delay(10);
|
||
|
|
}
|
||
|
|
UART1_TxString("\r\n");
|
||
|
|
SYS_Delay(1000);
|
||
|
|
}
|
||
|
|
}
|